TPE Injection Molding — Grades, Hardness and Overmolding (2026)
Table of Contents
TPE injection molding is how soft parts get made without vulcanisation. Thermoplastic elastomers melt and flow like plastic, then behave like rubber when they cool: 45 Shore A to 45 Shore D, elongation often above 400 %, and a grip that survives a decade of thumb traffic on a power tool handle. Because nothing cross-links chemically, scrap can be reground and the part can be molded in seconds rather than minutes.
The trap is that “TPE” is a family, not a material. Styrenic block copolymers (SBS, SEBS, SEPS), thermoplastic vulcanisates (TPV), thermoplastic polyolefins (TPO) and thermoplastic polyurethane (TPU) are quoted under the same three letters and behave nothing alike in a tool. SEBS bonds to polypropylene without an adhesive and refuses to bond to polyamide. TPV holds compression set at 120 °C and costs more. TPU takes abrasion that destroys SEBS and needs drying that SEBS does not. Specifying “TPE, Shore 60A” and stopping there is how projects lose six weeks.
This guide covers the family tree, the hardness ladder, the process windows, the bonding matrix for overmolding, mold design rules for soft material, shrinkage bands, the defect table, quality checks, and the RFQ fields that separate a workable quote from a change order.
The Snapshot
- Hardness range across the family runs 45 Shore A to 45 Shore D; most soft-touch grips land between 50A and 80A.
- Melt temperatures cluster at 175-230 °C for SEBS grades and 180-210 °C for TPV; mold temperature is low, typically 25-50 °C.
- Shrinkage is higher than engineering resins: 1.2-2.5 % for SEBS, 1.0-2.0 % for TPV, strongly dependent on wall thickness.
- SEBS grades need no drying; TPU and some filled TPV compounds absorb moisture and want 80-110 °C for 2-4 hours.
- TPE over PP bonds chemically with most SEBS and TPV grades; TPE over PA, PC or POM needs a bonding grade, a primer, or mechanical interlock.
- Regrind is workable at 20-30 % for non-cosmetic parts, with hardness and colour re-verified on the blend.
Table of Contents
- The Snapshot
- What TPE injection molding covers
- The TPE family tree
- Hardness selection from 45A to 45D
- TPE versus TPU versus silicone versus rubber
- Process windows for SEBS and TPV
- Drying and moisture behaviour
- Overmolding TPE onto rigid substrates
- Mold design for soft materials
- Living hinges and flex fatigue
- Defects and fixes
- Quality checks, cost drivers and the RFQ
- Frequently Asked Questions
- Sources
- Get a TPE injection molding quote
What TPE injection molding covers
Soft-touch and sealing parts are the two big categories. Soft-touch covers grips, handles, toothbrush bodies, wearable bands, tool overmolds, and consumer electronics bumpers where the requirement is feel plus friction plus durability. Sealing covers gaskets, weather seals, glass run channels, cable glands, and medical port seals where the requirement is compression set plus chemical compatibility.
TPE also replaced flexible PVC in a large share of medical and consumer applications, driven by plasticiser concerns and recyclability. A TPE part can be reground and remolded; a vulcanised rubber part cannot. That single fact drives most of the material substitution happening today, and it is why buyers increasingly ask for a TPE option alongside an existing rubber design.
What TPE does not do well: high continuous temperature above roughly 120-150 °C depending on grade, aggressive solvent exposure, and high-precision structural work at tight tolerance. If your part must hold ±0.05 mm across a 100 mm length, a soft TPE will fight you; the shrinkage moves with wall thickness and packing. Our injection molding service quotes TPE programs alongside the rigid substrate when the part is a two-material assembly, and our mold-making service handles the family or two-shot tool that carries both halves.
The TPE family tree
| Family | Hardness band | Temperature | Bonding strength | Typical use |
|---|---|---|---|---|
| SBS | 40A-90A | To about 70 °C | Good to PS, PP with modifiers | Low-cost grips, footwear, packaging |
| SEBS | 30A-95A | To about 120 °C | Excellent to PP, good to PE | Soft-touch grips, medical tubing, TPE overmolding |
| SEPS | 30A-90A | To about 120 °C | Similar to SEBS | Transparent soft parts, medical |
| TPV | 55A-50D | To about 135 °C | Excellent to PP, good to PA with grades | Automotive seals, glass run channels, appliance gaskets |
| TPO | 60A-60D | To about 100 °C | Good to PP | Automotive interior skins, bumpers |
| TPU | 60A-75D | To about 120 °C | Excellent to ABS, PC, PA | Abrasion parts, wheels, cable jackets, footwear |
The structural difference is where the “rubber” lives. SBS, SEBS and SEPS are styrenic block copolymers: polystyrene end blocks form physical cross-links that melt when heated, which is why the material is thermoplastic. TPV is a dynamically vulcanised blend of EPDM rubber particles inside a polypropylene matrix, so it behaves like rubber with better compression set and temperature resistance. TPU is a block copolymer of hard and soft segments with hydrogen bonding between chains, giving it abrasion resistance no styrenic TPE matches.
Price ladder, stated as relative indices rather than quotes: SBS is the cheapest, SEBS and TPO sit in the middle, TPV and TPU at the top. Medical and food-contact grades add a qualification premium regardless of chemistry. First Mold publishes TPE hardness from 45A to 45D with mold temperatures of 25-50 °C on their TPE page, which matches the general family behaviour; the grade-specific window still has to come from your compounder’s data sheet.
Hardness selection from 45A to 45D
| Shore hardness | Feel | Typical parts | Design note |
|---|---|---|---|
| 30-40A | Very soft, gel-like | Cushions, seals on fragile surfaces | Poor tear strength, needs generous radii |
| 45-55A | Soft grip | Toothbrush, wearable bands, medical tubing | Good balance of feel and durability |
| 60-70A | Firm grip | Power tool overmolds, handles, cable glands | Most common soft-touch band |
| 75-85A | Semi-rigid | Wheels, rollers, boots, seals | Bonds well, resists compression set |
| 90A-45D | Near-rigid | Housings, clips, load-bearing pads | Behaves like a tough plastic |
Two rules matter more than the number. First, hardness drifts with wall thickness and packing: a 1 mm section feels harder than a 4 mm section of the same compound because the thin wall cools faster and the soft phase has less freedom. Second, hardness changes with regrind and with colour masterbatch loading; a 2 % masterbatch can shift a 60A compound by 3-5 points, which is enough to fail a feel specification. Always approve a limit sample from production resin, not from a lab plaque.
If the part must feel identical to a competing product, specify hardness plus density plus a compression-set limit, because “60A” alone constrains only one of the three numbers that drive the hand feel.
TPE versus TPU versus silicone versus rubber
| Property | SEBS TPE | TPV | TPU | Silicone | EPDM rubber |
|---|---|---|---|---|---|
| Hardness band | 30A-95A | 55A-50D | 60A-75D | 20A-80A | 40A-90A |
| Abrasion resistance | Moderate | Moderate | Excellent | Low | Good |
| Temperature ceiling | About 120 °C | About 135 °C | About 120 °C | About 200 °C | About 150 °C |
| Compression set | Fair to good | Very good | Good | Excellent | Excellent |
| Bonds to PP | Yes | Yes | With grade | No | No |
| Bonds to ABS or PC | With grade | Rarely | Yes | No | No |
| Recyclable | Yes | Yes | Yes | Yes, limited | No |
| Relative material cost | Low | Medium-high | High | High | Medium |
| Cycle time | Fast | Fast | Fast | Slow, addition cure | Slow, vulcanisation |
Use the table as a first filter, then test. A 70A SEBS and a 70A TPV feel different, age differently, and price differently. Silicone remains the answer above 150 °C continuous or where the part must be steam sterilised repeatedly; TPE wins on cost, colour, bonding and recyclability below that line. Our silicone injection molding page covers the LSR route when temperature wins, and the TPU injection molding guide covers the abrasion-first cases.
Process windows for SEBS and TPV
| Parameter | SEBS grades | TPV grades | TPO grades |
|---|---|---|---|
| Barrel zone 1 | 160-180 °C | 170-190 °C | 170-190 °C |
| Barrel metering | 190-215 °C | 195-215 °C | 190-210 °C |
| Nozzle | 190-215 °C | 195-215 °C | 190-210 °C |
| Melt temperature | 175-230 °C | 180-210 °C | 180-210 °C |
| Mold temperature | 25-50 °C | 30-55 °C | 25-45 °C |
| Injection pressure | 30-70 MPa | 30-80 MPa | 30-70 MPa |
| Injection speed | Medium to fast | Medium | Medium |
| Holding pressure | 30-60 % of injection | 40-70 % | 30-60 % |
| Shrinkage | 1.2-2.5 % | 1.0-2.0 % | 1.0-2.0 % |
| Back pressure | Low, 5-15 bar | Low, 5-15 bar | Low, 5-15 bar |
Three process habits separate a stable TPE job from a fragile one. Keep melt temperature in the lower half of the range: TPE degrades quietly, and the first sign is usually a colour shift or an oily surface rather than a flash. Keep back pressure low, because the melt is shear-sensitive and excessive work in the screw produces stringing. And set hold pressure with a gate-freeze experiment rather than by copying a PP recipe: soft materials seal later than rigid ones because the gate is larger and the melt is compressible.
Screw design matters for the same reason. A general-purpose screw with a compression ratio around 2:1 to 2.5:1 handles most TPE grades; a screw optimised for polycarbonate will over-shear the melt. If your press runs both, keep a spare screw and plan on switching rather than compromising both jobs.
Drying and moisture behaviour
SEBS and TPO grades are normally supplied dry and do not need drying, which is one reason they are popular in shops without desiccant capacity. That statement is true only for unfilled, non-hygroscopic compounds stored properly. Three exceptions bite:
- TPU and TPU-alloy TPEs absorb moisture and must be dried at 80-110 °C for 2-4 hours; wet TPU produces silver streaks and a measurable drop in tensile strength.
- Mineral-filled and flame-retardant TPV compounds can carry surface moisture that shows as splay on the first shots of a cold start.
- Regrind stores moisture on its larger surface area, so a 30 % regrind stream behaves differently after a humid weekend than virgin pellets.
Ask for the compounder’s moisture specification in ppm, not “pre-dried”. Then verify at the hopper with a moisture analyser on the first shift and after any weekend stop. It is a five-minute check that prevents a full shift of cosmetic rejects.
Overmolding TPE onto rigid substrates
Overmolding is where most TPE projects live and where most fail. There are three routes, and choosing the wrong one costs either money or bond strength.
| Route | How it works | Tool cost | Cycle penalty | Best for |
|---|---|---|---|---|
| Two-shot | Both materials in one tool, rotating platen or index | Highest | Low, one setup | High volume, tight bond, cosmetic parts |
| Insert overmolding | Rigid insert loaded into a second tool | Medium | High labour unless automated | Medium volume, simple geometry |
| Pick and place | Separate tools, robot transfers | Medium | Medium, handling risk | Low volume, prototyping |
Bonding is chemistry plus surface. SEBS and TPV bond to polypropylene because the olefin phase is compatible with the PP surface; that is why the most common soft-touch part is TPE over PP. Bonding to ABS, PC or PA needs a grade formulated with polar groups, a primer, or a mechanical interlock such as through-holes, dovetails or a textured surface. A 0.5 mm undercut or a 10-15° dovetail wall routinely turns a peel failure into a cohesive failure, which is what you want.
Process rules that decide whether the bond holds:
- Preheat the substrate to 50-70 °C for PA and PC; a cold substrate chills the melt at the interface before wetting completes.
- Fill the TPE from the edge of the bond area inward so air escapes rather than being trapped at the interface.
- Keep the interface shear high enough to wet, but avoid jetting, which folds air into the bond line.
- Design a 1.5-2.5 mm TPE wall over the substrate; thinner than 1 mm the melt freezes before it wets, thicker than 3 mm the shrink differential pulls the bond apart.
- Validate with a peel or tensile test on production parts, not on lab plaques, and record the failure mode (cohesive versus adhesive).
Our overmolding service and the overmolding guide cover tool architecture and substrate preparation in more depth; the two-shot versus overmolding comparison helps when the decision is between processes rather than materials.
Mold design for soft materials
Soft material changes tool design in ways that beginners underestimate:
- Gates. Bigger than for rigid resins. A small gate shears the melt and leaves a string or a tear mark; a 1.0-1.5 mm edge or fan gate is normal on a 60A part. Avoid pin gates under 0.6 mm.
- Runners. Full-round, generously sized, and balanced. Pressure drop in a long thin runner is paid for with flash elsewhere.
- Venting. Soft melts fill fast and trap air: 0.02-0.03 mm vents at the parting line and at flow ends, plus ejector-pin venting on deep draws.
- Draft. 1-2° on vertical walls. Soft parts grip steel, so a zero-draft wall will tear on ejection rather than slide.
- Ejection. Stripper plates and air assist beat ejector pins: pins punch through soft material at surprisingly low force. Design ejection area, not ejection points.
- Cooling. Uniform cooling matters more than fast cooling: uneven mold temperature on a 2 mm soft wall produces visible flow lines and a hard-to-control shrink.
- Steel. Softer tool steels are acceptable because cavity pressures are low, but abrasive fillers and glass-filled TPV need hardened inserts. For family tools carrying both PP and TPE, harden the TPE side if the filler load differs.
Our DFM checklist covers the generic rules; the TPE-specific addition is gate size, ejection area, and a bond-area review on every overmolded feature.
Living hinges and flex fatigue
TPE is the best material family for living hinges after PP homopolymer, and for some geometries it is better because it survives millions of cycles without whitening. The design rules are geometric rather than chemical:
- Hinge thickness 0.25-0.4 mm for a part in the 60-90A range; thicker hinges stiffen and crack, thinner ones tear.
- Hinge length at least 2-3 times the thickness, with a smooth radius at each end.
- Orient the melt flow across the hinge, not along it: molecules aligned across the hinge line resist fatigue.
- Avoid gates near the hinge; shear history at the hinge line is the single biggest cause of early failure.
- Design the hinge to close through its full travel without over-centre stress; a hard stop at 180° protects it.
Test flex fatigue on a fixture at the intended cycle rate rather than assuming a number. A hinge that survives 10,000 cycles in a lab at one cycle per second may fail at 50,000 in the field because temperature and hand force change the strain.
Defects and fixes
| Defect | Likely cause | Fix |
|---|---|---|
| Flow marks or tiger stripes | Cold melt, slow fill, uneven mold temperature | Raise melt 5-10 °C, increase injection speed, balance cooling |
| Silver streaks | Moisture in TPU or filled compound, air entrapment | Dry at 80-110 °C, add venting, slow the first-stage fill |
| Delamination on overmold | Cold substrate, contaminated surface, wrong grade | Preheat substrate, clean with IPA, switch to a bonding grade |
| Short shot | Low pressure, cold mold, thin wall over long flow | Raise pressure and speed, raise mold temperature, add a gate |
| Flash | Over-packing, worn parting line, excessive hold | Reduce hold pressure, inspect parting line, verify clamp tonnage |
| Stringing or drooling | Over-heated melt, small gate, long decompression | Lower melt temperature, enlarge gate, adjust suck-back |
| Ejector marks or tears | Pin ejection on soft material, no draft | Stripper plate, air assist, add draft |
| Warpage | Uneven cooling, asymmetric wall, packing imbalance | Balance circuits, equalise walls, tune packing |
| Colour streaks | Poor masterbatch dispersion, low back pressure | Raise back pressure slightly, use a pre-compounded colour |
| Air traps or bubbles | Missing vents, jetting, wrong gate location | Add vents at flow ends, adjust gate, slow initial injection |
| Hard or brittle parts | Over-heating, regrind contamination, wrong grade | Verify melt temperature, cap regrind, check lot certificate |
Quality checks, cost drivers and the RFQ
Soft parts need different acceptance criteria than rigid ones. Dimensional inspection alone misses the failures that matter.
| Check | Method | Frequency | Acceptance |
|---|---|---|---|
| Hardness | Shore A or D durometer, 1 s or 15 s per standard | Per lot, 5 points per part | Within 3-5 points of target |
| Density | Immersion or pycnometer | Per lot | Within 0.02 g/cm3 of certificate |
| Tensile strength and elongation | ASTM D638 or ISO 527 | First article, per lot | Per material certificate |
| Compression set | ASTM D395, 22 h at 70 °C | First article, per lot on sealing parts | Per drawing, typically under 30 % |
| Tear strength | ASTM D624 | First article | Per drawing |
| Bond strength | Peel or tensile on overmolded parts | First article, per shift sample | Cohesive failure preferred |
| Flex fatigue | Fixture cycling | Design validation | Per service requirement |
| Cosmetic | Visual against limit sample | 100 % on visible parts | No flow marks on A-surface |
Cost drivers, in order of impact: material price per kilogram (TPV and TPU carry a premium), cycle time (soft parts run fast, but thick sections cool slowly), yield (flash and cosmetic rejects dominate scrap), regrind percentage, and tool amortisation. Lead time follows the tool, not the material: a simple single-cavity TPE tool takes 3-5 weeks, a two-shot tool with a rotating platen 6-10 weeks, plus 1-2 weeks for sampling and bond validation.
The 12-field RFQ checklist:
- Part drawing with critical dimensions and bond areas highlighted.
- Shore hardness target with a tolerance band, plus a physical limit sample if available.
- Family: SEBS, TPV, TPO, TPU, or “recommend and justify”.
- Colour, finish, and whether the surface is visible.
- Rigid substrate material and its surface condition for overmolding.
- Annual volume, launch volume, and expected lifetime.
- Process preference: two-shot, insert, or pick and place.
- Regrind policy and recycled content target.
- Temperature, chemical and UV exposure in service.
- Compression-set or flex-fatigue requirement with test method.
- Regulatory status: food contact, medical, automotive.
- Validation deliverables: FAI, hardness and density records, bond test report, PPAP level.
Frequently Asked Questions
Is TPE the same as TPU?
No. TPU is one member of the thermoplastic elastomer family, but it behaves differently: higher abrasion resistance, higher price, harder to bond to polypropylene, and it needs drying. TPE usually refers to the styrenic or olefinic families (SEBS, SBS, TPV, TPO) in everyday sourcing conversation.
What Shore hardness should I choose for a soft-touch grip?
Most grips land between 50A and 70A. Below 45A the part feels sticky and tears easily; above 80A it stops feeling soft. Approve a physical sample in production resin, because masterbatch and wall thickness shift the hand feel by several points.
Can TPE be overmolded onto polypropylene?
Yes, and it is the most common combination. SEBS and TPV grades bond chemically to PP without a primer. Push bond strength further with a 10-15° dovetail or a 0.5 mm undercut, and preheat the substrate to 50-70 °C before the second shot.
Does TPE need drying before molding?
SEBS and TPO normally do not. TPU and some filled TPV compounds do: 80-110 °C for 2-4 hours is typical. Regrind holds moisture on its larger surface area, so verify with a moisture analyser after any humid stop rather than trusting a label.
What is the maximum service temperature for TPE?
About 120 °C continuous for SEBS, 135 °C for TPV, and 120 °C for TPU. Above that, silicone or a thermoset rubber is usually the correct answer. Short-term peaks can run higher, but verify with the compounder rather than extrapolating.
Why does my TPE part show flow marks?
Flow marks come from a cold melt front meeting a warm one, or from uneven mold temperature. Raise the melt 5-10 °C, raise injection speed, and balance the cooling circuits so the cavity fills with a uniform front. On textured parts, add 0.5-1° of extra draft so the texture does not drag.
Can TPE parts be recycled?
Yes, which is a major advantage over vulcanised rubber. Clean production scrap can be reground at 20-30 % for non-cosmetic parts, with hardness and colour re-verified. Post-consumer recycling is limited by collection, not by the polymer.
How thick should an overmolded TPE layer be?
1.5-2.5 mm over the substrate. Below 1 mm the melt freezes before it wets the interface and the bond fails; above 3 mm the shrink differential between the soft and rigid materials generates peel stress at the edges.
What causes delamination in two-shot molding?
Three usual suspects: a cold or contaminated substrate, a non-bonding grade used where bonding was assumed, and gate placement that traps air in the bond line. Preheat the insert, clean it, verify the grade’s substrate compatibility, and fill from the bond edge inward.
How tight a tolerance can TPE hold?
Loosely compared with engineering plastics: ±0.1 mm on a 20 mm feature is realistic, and tighter values need a capability study. Soft material compresses under measurement, so specify the measurement force and method on the drawing.
Is TPE food-safe or medical grade?
Grades exist for both, but the grade must carry the declaration. Ask for FDA food-contact compliance or ISO 10993 biocompatibility data on the specific compound, not on the family. Medical TPE programs also need extractables and leachables review if the part contacts fluids.
Can TPE replace PVC in medical tubing?
Yes, and it is a common substitution. Expect to re-qualify: TPE has different kink resistance, different slip, and different bond strength to connectors. Run a pilot lot and test the assembly, not just the tubing.
Sources
- https://firstmold.com/guides/tpe-plastic/ - competitor TPE property data, the 45A-45D hardness band and 25-50 °C mold temperature.
- https://firstmold.com/tips/tpu-vs-tpe/ - competitor comparison of TPE and TPU behaviour.
- https://firstmold.com/overmolding-service/ - two-shot and insert overmolding process descriptions.
- https://firstmold.com/tpu-injection-molding/ - TPU process window used in the comparison table.
- https://www.kraiburg-tpe.com/en/ - compounder technical background on styrenic and vulcanisate TPE families.
- https://en.wikipedia.org/wiki/Thermoplastic_elastomer - polymer background and family definitions.
- https://www.astm.org/standards/plastics-standards.html - ASTM test methods for hardness, tensile, tear and compression set.
Get a TPE injection molding quote
Send the drawing, the hardness and family requirement (or let us recommend one), the rigid substrate if the part is overmolded, and your annual volume. We will return a cavity-count recommendation, a tooling band for two-shot versus insert, a bond-validation plan with the test method named, and a unit cost tied to a stated cycle time. If the material choice is still open, the material comparison guide and the plastic material selection guide give you the shortlist before tooling starts.
Get a quote or talk to an engineer about your soft-touch or sealing part. For automotive sealing and interior work, the automotive injection molding guide covers the validation stack that sits on top of the material choice.
NEXT STEP
Ready to Start Your Project?
Send us your requirements — our team responds within 24 hours. Pricing and a realistic lead time come with the reply.
Written by
Ray ChanExport Brand Manager · Injection Molding, Mold Making & DFM. Ray helps global importers and integrators source factory-direct plastic parts and tooling.